My Encore error
- Spidermonkey
- Posts: 16
- Joined: Thu Jan 18, 2007 6:14 pm
- Location: Bronxville, NY
My Encore error
I just installed Encore Pro and My Encore. I haven't yet collected any data on my smartcard. When I try to open My Encore, I get an error message stating:
Unable to access the EncorePro database.
MyEncore will close...
Index #0
Message: SQL Server does not exist or access denied.
LineNumber: 0
Source: .Net SqlClient Data Provider
Procedure: ConnectionOpen (Connect()).
Do I need to have actual data downloaded, or is something else wrong?
Susan
Unable to access the EncorePro database.
MyEncore will close...
Index #0
Message: SQL Server does not exist or access denied.
LineNumber: 0
Source: .Net SqlClient Data Provider
Procedure: ConnectionOpen (Connect()).
Do I need to have actual data downloaded, or is something else wrong?
Susan
Susan, check to see if you followed these instructions:
viewtopic.php?t=10149
Also, make sure you are using a USB:
When you open Encore Pro, click on “Preferences” (upper right part of page), and then “System Settings”, make sure that “USB” is selected under Smart Card Reader.
Others can chime in here. I'm just trying to help until someone computer literate gets here. ..............
viewtopic.php?t=10149
Also, make sure you are using a USB:
When you open Encore Pro, click on “Preferences” (upper right part of page), and then “System Settings”, make sure that “USB” is selected under Smart Card Reader.
Others can chime in here. I'm just trying to help until someone computer literate gets here. ..............
You have to have Respironics EncorePro installed and working first.
Then download your data from the SmartCard to the SQL database using EncorePro software under your patient profile.
Then for an alternate report, while the EncorePro database is still running (denoted by green play arrow on task bar, red box means database is not running, right click and make sure it is running, if not select "start"). The MyEncore should access the database and pull up the report.
Then download your data from the SmartCard to the SQL database using EncorePro software under your patient profile.
Then for an alternate report, while the EncorePro database is still running (denoted by green play arrow on task bar, red box means database is not running, right click and make sure it is running, if not select "start"). The MyEncore should access the database and pull up the report.
- Spidermonkey
- Posts: 16
- Joined: Thu Jan 18, 2007 6:14 pm
- Location: Bronxville, NY
Thanks for the information thus far. I'm continuing to have issues, this time with the card reader itself. I have the Infineer card reader (purchased from CPAP.com).
There was no driver that came with it. I downloaded the driver software from Mako-Tech.com but am still having no luck. Neither the Mako software nor Encore Pro is recognizing the card reader, and the green light does not light when it is plugged in. Could I have a dud?
Susan
There was no driver that came with it. I downloaded the driver software from Mako-Tech.com but am still having no luck. Neither the Mako software nor Encore Pro is recognizing the card reader, and the green light does not light when it is plugged in. Could I have a dud?
Susan
- jskinner
- Posts: 1473
- Joined: Sat Aug 26, 2006 9:21 pm
- Location: Greenwich, Nova Scotia, Canada
- Contact:
Re: My Encore error
Susan,Spidermonkey wrote: Do I need to have actual data downloaded, or is something else wrong?
A number of issues here:
First you have the wrong version of MyEncore. Please see this thread viewtopic.php?t=16915 or get the correct version from http://lewiston.mit.edu/myencore/myencore15b7.msi (Again if ANYONE knows who to contact to get this link updated please let me know or contact them yourself. This is unnecessarily frustrating for everyone)
Second yes you will need some data from your machine for it to work...(Although this was not the cause of the error you where seeing)
As blarg pointed out, make sure you install the correct Smart card driver as the Mako-Tech.com one will not work. The correct one is http://www.two-factor.com/driver/DT3500 ... o_v1_3.exe Also make sure that you install it *after* Encore Pro has been installed.
There IS a driver on the Encore Pro CD. If you "Explore" the CD, you will find a directory named "Smart Card Readers" that has the proper card reader install program: "Setup.exe".Spidermonkey wrote:Thanks for the information thus far. I'm continuing to have issues, this time with the card reader itself. I have the Infineer card reader (purchased from CPAP.com).
There was no driver that came with it. I downloaded the driver software from Mako-Tech.com but am still having no luck. Neither the Mako software nor Encore Pro is recognizing the card reader, and the green light does not light when it is plugged in. Could I have a dud?
Susan
Best wishes,
Den
(5) REMstar Autos w/C-Flex & (6) REMstar Pro 2 CPAPs w/C-Flex - Pressure Setting = 14 cm.
"Passover" Humidification - ResMed Ultra Mirage FF - Encore Pro w/Card Reader & MyEncore software - Chiroflow pillow
User since 05/14/05
"Passover" Humidification - ResMed Ultra Mirage FF - Encore Pro w/Card Reader & MyEncore software - Chiroflow pillow
User since 05/14/05
Jskinner --
Am I wrong to refer people to post? viewtopic.php?t=10149
Supposedly, that was the best of the best instructions.
If it's wrong, and if and when you have time, could you copy it and amend it for future installers?
And finally, How do/did you know she has the wrong version of MyEncore?
Love that we have a computer guru aboard.
Am I wrong to refer people to post? viewtopic.php?t=10149
Supposedly, that was the best of the best instructions.
If it's wrong, and if and when you have time, could you copy it and amend it for future installers?
And finally, How do/did you know she has the wrong version of MyEncore?
Love that we have a computer guru aboard.
- jskinner
- Posts: 1473
- Joined: Sat Aug 26, 2006 9:21 pm
- Location: Greenwich, Nova Scotia, Canada
- Contact:
Nope that was a good post. Those are very detailed (almost painfully so) step by step instructions. Following those directions would certinaly avoid the problem but it just seemed better to get strait to what the problem appeared to be. The very long step by step instructions could be summarized as follows:Linda3032 wrote:Am I wrong to refer people to post?
1. Install Encore Pro
2. Install Encore Pro specific DT3500 Smartcard drivers
3. Install add on applications (MyEncore and/or EPA)
The error message that was posted is what normally happens if people try to use MyEncore 1.04 with Encore Pro 1.6. They need to use the MyEncore 1.5 beta version to avoid this. This problem keeps comming up over and over again. This problem could be virtually eliminated if someone would just update the link to MyEncore on cpaptalk.com (and Derek's site). Multiple messages regarding this issue sent to the form admins have gone unanswered.Linda3032 wrote: And finally, How do/did you know she has the wrong version of MyEncore?
Last edited by jskinner on Sun Jan 28, 2007 5:51 pm, edited 1 time in total.
- Spidermonkey
- Posts: 16
- Joined: Thu Jan 18, 2007 6:14 pm
- Location: Bronxville, NY
- jskinner
- Posts: 1473
- Joined: Sat Aug 26, 2006 9:21 pm
- Location: Greenwich, Nova Scotia, Canada
- Contact:
At what point do things not work? When you go into Encore Pro and try to do a download?Spidermonkey wrote:I am completely baffled. Nothing works. I uninstalled everything and then followed instructions to a T. The card reader is still not being recognized.Maybe I do have a lemon--I have no idea what else to do!






