Need help to increase my airflow on my Remstar Plus C-flex

General Discussion on any topic relating to CPAP and/or Sleep Apnea.
Guest

Need help to increase my airflow on my Remstar Plus C-flex

Post by Guest » Wed Mar 27, 2013 7:58 pm

Can someone help me find a way to increase the airflow on my machine? i have a setting of 6 and would like to increase it to a 10. thank you in advance

Wulfman...

Re: Need help to increase my airflow on my Remstar Plus C-flex

Post by Wulfman... » Wed Mar 27, 2013 8:18 pm

Guest wrote:Can someone help me find a way to increase the airflow on my machine? i have a setting of 6 and would like to increase it to a 10. thank you in advance
If you've got an "old" Legacy model, these should work.

Den



REMstar Plus CPAP w/C-Flex

1. With the machine plugged into a wall outlet, unplug the cord from the back of the CPAP. Then, press and hold down the two user buttons below the display screen while plugging the cord back into the CPAP, and continue to hold the buttons down until the CPAP beeps. This will indicate that the CPAP is in the Therapy Setup Menu.

2. The display will first show the number of hours the machine has been used. To erase this total and begin again at zero, press and hold the ramp or humidifier button. An “X” will appear on the display. Hold the button down until the time change to “0” and the “X” disappears.

To skip this setting or continue, press the right user button.

3. The elevation setting will appear next. To change this setting, press the ramp or humidifier button until the correct setting appears. Here are the elevation settings: 1 = less than 2,500 ft.; 2 = 2,500 to 5,000 ft.; 3 = 5,001 to 7,500 ft.

To skip this setting or continue, press the right user button.

4. The therapy mode will appear, either CPAP or CFLEX. To change this setting, press the ramp or humidifier button until the correct setting appears.

To skip this setting or continue, press the right user button.

5. The CPAP pressure will appear. To change this setting, press the ramp or humidifier button until the correct setting appears.

To skip this setting or continue, press the right user button.

6. The CPAP fine adjustment setting will appear. This setting allows you to calibrate your CPAP pressure to a manometer. We suggest you do not try to adjust this setting.

To skip this setting or continue, press the right user button.

7. The CFLEX setting will appear if you selected the CFLEX mode in number 4 above. A setting of 1 offers the least drop in pressure, 3 offers the most. To change this setting, press the ramp or humidifier button until the correct setting appears.

To skip this setting or continue, press the right user button.

8. The ramp time will appear next. It may be set for 0 to 45 minutes in 5 minute increments. To change this setting, press the ramp or humidifier button until the correct setting appears.

To skip this setting or continue, press the right user button.

9. The ramp starting pressure will appear. To change this setting, press the ramp or humidifier button until the correct setting appears.

To skip this setting or continue, press the right user button.

10. The patient disconnect setting will appear. This sounds an alarm when there is a mask leak and turns the airflow off. 1 = On; 0 = Off. To change this setting, press the ramp or humidifier button until the correct setting appears.


There are no other settings available. Press the pressure start/stop button to exit the menu or press the right user button to scroll through the settings again.

.

Guest

Re: Need help to increase my airflow on my Remstar Plus C-flex

Post by Guest » Wed Mar 27, 2013 8:44 pm

Thank you . It did not seem to work . This machine is about 6 months old if that helps

Wulfman...

Re: Need help to increase my airflow on my Remstar Plus C-flex

Post by Wulfman... » Wed Mar 27, 2013 9:03 pm

Guest wrote:Thank you . It did not seem to work . This machine is about 6 months old if that helps
Yep. That definitely makes a difference. They've re-used the same model names for numerous generations of machines.

Here's a link to download an instruction "card". Copy and paste it into your browser and take out the spaces I put in there.

http : / / www . directhomemedical . com/machines-cpap-bipap/prsystemone-cpap-bipap-patient-quickstart-guide . pdf


Den

.