How often do you replace nasal pillows on your mask?

General Discussion on any topic relating to CPAP and/or Sleep Apnea.
proboscis
Posts: 5
Joined: Thu Jan 06, 2011 7:48 am
Location: Lake Hiawatha, NJ

Re: How often do you replace nasal pillows on your mask?

Post by proboscis » Fri Jan 27, 2012 12:26 pm

Robespierre wrote:
proboscis wrote:Have you tried boiling the pillows? I have the Swift FX and they start to leak every 2-3 weeks. I found out about boiling them on this forum. Just boil a pot of water, dump in some baking soda, and drop the pillows in for around 30 minutes. Then rinse off with cold water. They seal like new after that.
When you put the pillows in, do you turn off the heat or keep it on a low boil for 30 minutes? If you turn the heat off, do you cover the pot?

And, why the baking soda?
yep, I leave it on a low boil, and use a large metal straining spoon to hold the pillows under (otherwise they'll keep floating). I didn't even know what the baking soda was for, just that the people doing it had good results. But greg-g had a great explanation.

User avatar
chunkyfrog
Posts: 34545
Joined: Mon Jul 12, 2010 5:10 pm
Location: Nowhere special--this year in particular.

Re: How often do you replace nasal pillows on your mask?

Post by chunkyfrog » Fri Jan 27, 2012 12:31 pm

I have toyed with the idea of putting them in the countertop steamer.
Auto shut-off, too--just to save my forgetful self from disaster.

_________________
Mask: AirFit™ P10 For Her Nasal Pillow CPAP Mask with Headgear
Additional Comments: Airsense 10 Autoset for Her

Wrathwielder
Posts: 12
Joined: Sat Mar 26, 2011 9:55 pm

Re: How often do you replace nasal pillows on your mask?

Post by Wrathwielder » Fri Jan 27, 2012 1:24 pm

Hiya!

Thanks for the tip! Nothing worse than feeling that little air leak, not to mention the stupid whistling sound when I get rainout with the Swift - keep flicking the thing with my finger to clear the water - but thank God for cpaps! I can't complain...

BTW, how much baking soda should I add when I boil the pillows? (figure I'd use a small pan like you'd boil hot dogs in...)

Thanks!

-Greg

greg-g
Posts: 219
Joined: Sun Dec 20, 2009 1:07 am
Location: Tasmania Australia

Re: How often do you replace nasal pillows on your mask?

Post by greg-g » Fri Jan 27, 2012 7:09 pm

Wrathwielder wrote:Hiya!

BTW, how much baking soda should I add when I boil the pillows? (figure I'd use a small pan like you'd boil hot dogs in...)
1 teaspoon seems to be ample in a small saucepan

_________________
Mask: Swift™ FX Nasal Pillow CPAP Mask with Headgear
Humidifier: S9™ Series H5i™ Heated Humidifier with Climate Control
Additional Comments: CMS-50F, Night Vision camera, Hose hanger, ResScan 3.16, Modified Swift FX with head band and air diffuser.

User avatar
bayourest
Posts: 389
Joined: Wed Dec 01, 2010 9:16 am
Location: Connecticut

Re: How often do you replace nasal pillows on your mask?

Post by bayourest » Sat Jan 28, 2012 5:30 am

i've just ordered a swift LT to try out so this pillow question is relevant to me:
do you boll the pillows when new or before using them? or do you wait til they seem to be leaking?
thanks a lot. I have not yet received my pillows etc so this info is very helpful

greg-g
Posts: 219
Joined: Sun Dec 20, 2009 1:07 am
Location: Tasmania Australia

Re: How often do you replace nasal pillows on your mask?

Post by greg-g » Sat Jan 28, 2012 5:44 am

Boiling pillows is a way to resurrect pillows that don't work as well as they used to and would otherwise be discarded.
I'm a cheapskate and in Australia they aren't covered buy insurance.

_________________
Mask: Swift™ FX Nasal Pillow CPAP Mask with Headgear
Humidifier: S9™ Series H5i™ Heated Humidifier with Climate Control
Additional Comments: CMS-50F, Night Vision camera, Hose hanger, ResScan 3.16, Modified Swift FX with head band and air diffuser.