My numbers and a couple questions

General Discussion on any topic relating to CPAP and/or Sleep Apnea.
REP
Posts: 12
Joined: Sat Dec 09, 2006 9:31 am
Location: Arnold MO

My numbers and a couple questions

Post by REP » Sun Jan 14, 2007 8:57 am

I was able to get my numbers off my machine and I have a couple questions. What does the leak number mean. Is that good or bad? Would this show any mouth breathing that may be going on? I assuming that AHI is ok I was tested at 18.7 in my SS. And finally what does the AI and HI numbers represent? I have the Resmed S8 elite.

LEAK:0.12L/s
AHI:4.4
AI:0.2
HI:4.2


Thanks all

_________________

CPAPopedia Keywords Contained In This Post (Click For Definition): resmed, AHI

Dave

ufo13
Posts: 388
Joined: Sat Jul 16, 2005 8:35 am
Location: Area 51

Very good!

Post by ufo13 » Sun Jan 14, 2007 11:22 am

Dave:

You are doing very well! Your leak numbers are very good, ie: 0.12l/s =0.12x60sec=7.2l/m, GREAT! Your apnea index AI (the most important one) 0.2 almost perfect treatment, and the HI (partial obstructions) not bad at all IMO. Yes your AHI being under 5.0 is considered normal!


Hope this helps,

Steve,
ufo13


_________________
Mask: AirFit™ P10 Nasal Pillow CPAP Mask with Headgear
Additional Comments: Also use ResMed N30 and ResMed P30i

lvwildcat
Posts: 384
Joined: Mon Nov 20, 2006 11:00 am
Location: Las Vegas,baby!

Post by lvwildcat » Sun Jan 14, 2007 11:49 am

Thanks for that answer to the poster,Steve-that cleared up a question I had.
My AI usually runs 0.0 and AHI between 3.7-4.5 OK I can stop worrying and accept these numbers.


_________________
Mask
Additional Comments: Machine:Resmed S7 Elite; Oracle Mask(YES! My DREAM mask!!)
Image
Image

REP
Posts: 12
Joined: Sat Dec 09, 2006 9:31 am
Location: Arnold MO

Post by REP » Sun Jan 14, 2007 4:34 pm

Does that leak number mean only mask leaks or is it mouth leaking also?
Dave

User avatar
dsm
Posts: 6996
Joined: Mon Jun 20, 2005 6:53 am
Location: Near the coast.

Post by dsm » Sun Jan 14, 2007 6:16 pm

On a Resmed S8, if you have the mask set correctly in the menu, any leak shown is a genuine air leak but 0.12 is on the low side.

I will get figures as low as 0.02 on one machine I have. I also have an S8 Escape & that will typically be 0.00 (I use a Resmed Ultra Mirage F/F mask).

The HI indication is usually higher on Resmed machines that if you slept with a Respironics machine & looked at the nights data. On My Remstar AUTO I rarely got the same high HI numbers I get using Resmed machines. This difference hasn't caused me any real concern. I did wonder why Resmed machines show higher HI #s in general. Many other here have reported this same issue.

All in all your numbers are good allowing that the biggest part of the AHI# is the HI part.

Good going

DSM

xPAP and Quattro std mask (plus a pad-a-cheek anti-leak strap)

User avatar
pedroski
Posts: 459
Joined: Mon Nov 27, 2006 12:54 am
Location: Bathurst, Australia
Contact:

Post by pedroski » Sun Jan 14, 2007 7:51 pm

Does that leak number mean only mask leaks or is it mouth leaking also?
Hi Dave,

That's all leaks mate. I doubt if your mouth leaking much with a leak figure of 0.12. A better indicator is are you waking up with a dry mouth. I use the Swift as well, and I find if I open my mouth the resulting rush of air is quite unpleasant and not something I could sleep through. Like the other guys said, your Apnoea Hypopnea Index (AHI) figures are pretty good, so I wouldn't worry too much about leaks.

Good Luck,

Peter