change pressure on remstar choice and tranquility quest

[catbirdgirl]

Am probably borrowing an old machine from my mom rather than renting since mine is in the shop, so does anyone know how to adjust the pressure?

[6PtStar]

If I remember right there is little door on the bottom right of the machine. If you open it there is a screwdriver slot that says pressure. You have to turn it and set it with a water manometer. Does not have pre programed pressure settings.

Jerry

[dsm]

If I remember right there is little door on the bottom right of the machine. If you open it there is a screwdriver slot that says pressure. You have to turn it and set it with a water manometer. Does not have pre programed pressure settings.

Jerry

Exactly

DSM

(Tranquility Quest that is )

[jules]

either this one?





the top comes off the tower to set it but it still needs a manometer - two dials inside - one is pressure - one is ramp

[aquavion]

Hello, this is my first post.

I have an old RemStar Choice and would like to change the pressure settings from the current 6 cm H2O. I tried taking off the case of the unit by removing the 3 screws on the bottom but the removal was halted by the interference of 3 cables which connected to the circuit board and which were extremely difficult to get at and likely even more difficult to reconnect so I didn't go any further. The posts on this subject seemed to indicate there was an external way to get at the trim pots but I have not been able to find the openings to the pots. For those who have posted about this, can you be any more specific about exactly where the external access is located on this unit ? Thanks for any help you might be able to provide in this regard.

[Wulfman...]

Hello, this is my first post.

I have an old RemStar Choice and would like to change the pressure settings from the current 6 cm H2O. I tried taking off the case of the unit by removing the 3 screws on the bottom but the removal was halted by the interference of 3 cables which connected to the circuit board and which were extremely difficult to get at and likely even more difficult to reconnect so I didn't go any further. The posts on this subject seemed to indicate there was an external way to get at the trim pots but I have not been able to find the openings to the pots. For those who have posted about this, can you be any more specific about exactly where the external access is located on this unit ? Thanks for any help you might be able to provide in this regard.

I have the service manual ( in .pdf form ) for the "Choice" models, which clearly shows how to change it (and more).
If you wish me to send it to you, PM (private message) me with your email address and I'll shoot it to you. It's not all that big of a file.......less than 1 MB.


Den

.

[aquavion]

<r><QUOTE><s>

</s><e>

</e></QUOTE>
I have the service manual ( in .pdf form ) for the "Choice" models, which clearly shows how to change it (and more).<br/>
If you wish me to send it to you, PM (private message) me with your email address and I'll shoot it to you. It's not all that big of a file.......less than 1 MB.<br/>
<br/>

Many thanks to Wulfman for providing me a complete service manual on the RemStar "Choice" !!</r>

[chunkyfrog]

So that is what a dinosaur looks like . . .

[Okie bipap]

I always thought dinosaurs were much bigger.

[zonker]

<r><QUOTE><s>

</s><e>

</e></QUOTE>
I have the service manual ( in .pdf form ) for the "Choice" models, which clearly shows how to change it (and more).<br/>
If you wish me to send it to you, PM (private message) me with your email address and I'll shoot it to you. It's not all that big of a file.......less than 1 MB.<br/>
<br/>

Many thanks to Wulfman for providing me a complete service manual on the RemStar "Choice" !!</r>

just to give you a heads up, if you want to quote someone here on the forum, just use the quotation marks in the upper right hand side. otherwise, it looks like what i just quoted above.