Repairing a machine

General Discussion on any topic relating to CPAP and/or Sleep Apnea.
treydawgmt
Posts: 24
Joined: Wed Oct 22, 2014 8:24 pm

Repairing a machine

Post by treydawgmt » Thu Mar 31, 2016 10:26 am

Hello all,

The ResMed S9 AutoSet with the H5i humidifier that I got for free a few months ago has an issue. It is VERY VERY VERY noisy all of a sudden. It sounds like air is leaking. I'm 99% sure it is the humidifier's black rubber seal - it is bent and twisted a bit. I try smoothing it out, and then inserting the humidifer into the CPAP part itself, but it still sounds like air is leaking. Any thoughts on having it tested/repaired versus maybe buying a new humidifier only? Since this was a used machine I'm not 100% sure it works totally right either, so depending on the cost of a repair it might be worth it to have the whole thing checked over. It's my second machine I use at work, so it would not be a huge deal to be without it for a few days/weeks.

Any thoughts, suggestions, comments form anyone that has done this? Ideas for the best place to send it?

Thanks,

Matt

_________________
Mask
Additional Comments: Sleep Mapper Data Uploader

User avatar
stienman
Posts: 89
Joined: Thu Feb 04, 2016 12:40 pm
Location: Ann Arbor, MI

Re: Repairing a machine

Post by stienman » Thu Mar 31, 2016 11:36 am

Just in case it's something else, try it without the humidifier attached. Disconnect the humidifier, attach the hose directly to the cpap, and see if the noise is still present.

_________________
Mask: AirFit™ P10 Nasal Pillow CPAP Mask with Headgear
Humidifier: S9™ Series H5i™ Heated Humidifier with Climate Control
Additional Comments: CMS50F PulseOx, Sleepyhead

treydawgmt
Posts: 24
Joined: Wed Oct 22, 2014 8:24 pm

Re: Repairing a machine

Post by treydawgmt » Thu Mar 31, 2016 12:29 pm

stienman wrote:Just in case it's something else, try it without the humidifier attached. Disconnect the humidifier, attach the hose directly to the cpap, and see if the noise is still present.
I tried that last night, it is still noiser than my home machine, but WAY better. Which is what makes me think it's just the humidifier.

_________________
Mask
Additional Comments: Sleep Mapper Data Uploader

User avatar
Sir NoddinOff
Posts: 4190
Joined: Mon May 14, 2012 5:30 pm
Location: California

Re: Repairing a machine

Post by Sir NoddinOff » Thu Mar 31, 2016 12:50 pm

If you get stuck and nothing works you might contact this repair facility ... I've used them before. Don't give up too early tho, maybe there's a simple fix out there.

http://www.acbio.com

_________________
Mask: AirFit™ F10 Full Face Mask with Headgear
Additional Comments: Sleepyhead software v.0.9.8.1 Open GL and Encore Pro v2.2.
I like my ResMed AirFit F10 FFM - reasonably low leaks for my ASV therapy. I'm currently using a PR S1 AutoSV 960P Advanced. I also keep a ResMed S9 Adapt as backup. I use a heated Hibernite hose. Still rockin' with Win 7 by using GWX to stop Win 10.

User avatar
palerider
Posts: 32299
Joined: Wed Dec 16, 2009 5:43 pm
Location: Dallas(ish).

Re: Repairing a machine

Post by palerider » Thu Mar 31, 2016 2:51 pm

treydawgmt wrote:Hello all,

The ResMed S9 AutoSet with the H5i humidifier that I got for free a few months ago has an issue. It is VERY VERY VERY noisy all of a sudden. It sounds like air is leaking. I'm 99% sure it is the humidifier's black rubber seal - it is bent and twisted a bit. I try smoothing it out, and then inserting the humidifer into the CPAP part itself, but it still sounds like air is leaking. Any thoughts on having it tested/repaired versus maybe buying a new humidifier only?
what black rubber seal?

there's a large clear silicone seal in the lid that seals the entire chamber, you don't even have to have the water tank in the humidifier.

_________________
Mask: Bleep DreamPort CPAP Mask Solution
Additional Comments: S9 VPAP Auto
Get OSCAR

Accounts to put on the foe list: dataq1, clownbell, gearchange, lynninnj, mper!?, DreamDiver, Geer1, almostadoctor, sleepgeek, ajack, stom, mogy, D.H., They often post misleading, timewasting stuff.

treydawgmt
Posts: 24
Joined: Wed Oct 22, 2014 8:24 pm

Re: Repairing a machine

Post by treydawgmt » Thu Mar 31, 2016 4:38 pm

palerider wrote:
what black rubber seal?

there's a large clear silicone seal in the lid that seals the entire chamber, you don't even have to have the water tank in the humidifier.
There is a black rubber gasket like thing around the circle shaped opening on the humidifier where the CPAP part goes in. It's by the part where the air goes into the water tank. I think this black rubber gasket is the problem. I'm unsure if its fixable by itself.

_________________
Mask
Additional Comments: Sleep Mapper Data Uploader

User avatar
palerider
Posts: 32299
Joined: Wed Dec 16, 2009 5:43 pm
Location: Dallas(ish).

Re: Repairing a machine

Post by palerider » Thu Mar 31, 2016 5:32 pm

treydawgmt wrote:There is a black rubber gasket like thing around the circle shaped opening on the humidifier where the CPAP part goes in. It's by the part where the air goes into the water tank. I think this black rubber gasket is the problem. I'm unsure if its fixable by itself.
ah, that seal. not sure how that's actually applied, may be glued in place. it comes out from flush with the inside of the chamber, then makes a v turn and goes back inward just a little.

so if you were looking at the bottom edge of the seal, from the front of the humidifier, in cross section, it'd be a bit like this:

Code: Select all

   /
  /
/_________
and the tube from the blower would go in above that.

_________________
Mask: Bleep DreamPort CPAP Mask Solution
Additional Comments: S9 VPAP Auto
Get OSCAR

Accounts to put on the foe list: dataq1, clownbell, gearchange, lynninnj, mper!?, DreamDiver, Geer1, almostadoctor, sleepgeek, ajack, stom, mogy, D.H., They often post misleading, timewasting stuff.

Sherri@acbio
Posts: 1
Joined: Fri May 06, 2016 1:02 pm

Re: Repairing a machine

Post by Sherri@acbio » Fri May 06, 2016 2:56 pm

90 percent of our CPAP repairs are completed within a week. We are the nation’s largest respiratory service provider, with three regional service centers. Our expert bio-medical technicians provide professional service for all of your CPAP needs.
Fast Turnaround. A certified technician will contact you within 48 hours.
Easy Shipping Options. We accept any shipping method.
No-Worry Repairs. Accurate offers a 90-day warranty on all repairs.
Never Pay More than Necessary. You’ll never pay more than you need to for repairs. In addition to repair, we offer reconditioned units at affordable prices.
email sherrim@acbio.com or call 888-327-7483 X211 for more info

User avatar
Sir NoddinOff
Posts: 4190
Joined: Mon May 14, 2012 5:30 pm
Location: California

Re: Repairing a machine

Post by Sir NoddinOff » Sat May 07, 2016 5:43 pm

Sherri@acbio wrote:90 percent of our CPAP repairs are completed within a week. We are the nation’s largest respiratory service provider, with three regional service centers. Our expert bio-medical technicians provide professional service for all of your CPAP needs.
Fast Turnaround. A certified technician will contact you within 48 hours.
Easy Shipping Options. We accept any shipping method.
No-Worry Repairs. Accurate offers a 90-day warranty on all repairs.
Never Pay More than Necessary. You’ll never pay more than you need to for repairs. In addition to repair, we offer reconditioned units at affordable prices.
email sherrim@acbio.com or call 888-327-7483 X211 for more info
I've used Accurate BioMed and they are a good repair service.

_________________
Mask: AirFit™ F10 Full Face Mask with Headgear
Additional Comments: Sleepyhead software v.0.9.8.1 Open GL and Encore Pro v2.2.
I like my ResMed AirFit F10 FFM - reasonably low leaks for my ASV therapy. I'm currently using a PR S1 AutoSV 960P Advanced. I also keep a ResMed S9 Adapt as backup. I use a heated Hibernite hose. Still rockin' with Win 7 by using GWX to stop Win 10.