first night, first timer

General Discussion on any topic relating to CPAP and/or Sleep Apnea.
User avatar
OkyDoky
Posts: 2870
Joined: Mon Aug 25, 2014 5:18 pm

Re: first night, first timer

Post by OkyDoky » Sat Feb 20, 2016 7:11 pm

palerider wrote:
dontknowhowtodeal wrote:I am sorry about supplying the name of the products but they are not on the list in the profile.
ResMed Airsense 10 Autoset for her
it is:
AirSense™ 10 AutoSet For Her CPAP Machine with HumidAir™ Heated Humidifier
Right I missed the For Her and am so used to telling them to type it in on other models. You can find it listed in the pull down menu just like Palerider listed it.
ResMed Aircurve 10 VAUTO EPAP 11 IPAP 15 / P10 pillows mask / Sleepyhead Software / Back up & travel machine Respironics 760

User avatar
OkyDoky
Posts: 2870
Joined: Mon Aug 25, 2014 5:18 pm

Re: first night, first timer

Post by OkyDoky » Sat Feb 20, 2016 7:21 pm

dontknowhowtodeal wrote:I am going to try again tonite wearing it to sleep but this time I will lie on bed instead of sitting in my recliner chair. Advice anyone?
I would try out the manual humidity and tube temperature settings. Your manual states the tube temperature can be adjusted down to 60 degrees. See if that helps the heated air feeling. It may not prevent rainout but if you have the machine lower than the tube it will run back into the humidifier.
Get the software running and then we can see what is happening. We will walk you through any specific problems you have.
ResMed Aircurve 10 VAUTO EPAP 11 IPAP 15 / P10 pillows mask / Sleepyhead Software / Back up & travel machine Respironics 760

User avatar
dontknowhowtodeal
Posts: 17
Joined: Sat Feb 20, 2016 4:44 pm

Re: first night, first timer

Post by dontknowhowtodeal » Sat Feb 20, 2016 7:23 pm

Also I just read this in another post and have experienced the similar sort of thing-
Sometimes I feel like I need a good deep breath

_________________
Mask
Additional Comments: amara view minimal contact full face mask, ResMed Airsense Autoset 10

itsjustme
Posts: 15
Joined: Tue Jun 16, 2015 10:57 am

Re: first night, first timer

Post by itsjustme » Sat Feb 20, 2016 7:25 pm

My first couple weeks were pretty tough. Several times I felt like taking the mask off and saying to heck with it. But after the first night that I managed to sleep a few hours with it I noticed that I didn't wake up with a headache, coughing, and needing a drink of water. After a while it will get easier, now I would never think of going to sleep without using the machine. I know it's rough but you have to hang in there and you will get used to it.

User avatar
Wulfman...
Posts: 6688
Joined: Mon Sep 01, 2014 6:41 pm
Location: Nearest fishing spot

Re: first night, first timer

Post by Wulfman... » Sat Feb 20, 2016 7:27 pm

dontknowhowtodeal wrote:Also I just read this in another post and have experienced the similar sort of thing-
Sometimes I feel like I need a good deep breath
Your minimum pressure may be too low. Lots of people need something around 7 or more to be able to breathe adequately.
And, if the Ramp is turned on, you may need to look at those settings, too.


Den

.
(5) REMstar Autos w/C-Flex & (6) REMstar Pro 2 CPAPs w/C-Flex - Pressure Setting = 14 cm.
"Passover" Humidification - ResMed Ultra Mirage FF - Encore Pro w/Card Reader & MyEncore software - Chiroflow pillow
User since 05/14/05

User avatar
Julie
Posts: 20028
Joined: Tue Feb 28, 2006 12:58 pm

Re: first night, first timer

Post by Julie » Sat Feb 20, 2016 9:05 pm

Breathe however you like - through your nose, your nose and mouth or just your mouth. It is best (especially with a nasal mask) to only breathe through your nose, but once asleep you can't control that, so if you think you're mouth breathing, a full face mask is best, allowing you to not lose Pap air that way, even if your mouth's open. Don't try to adapt to the machine's rhythm in any way - it's supposed to adapt to your breathing and respond by raising pressure if necessary, but you're not expected to do anything otherwise.

User avatar
palerider
Posts: 32299
Joined: Wed Dec 16, 2009 5:43 pm
Location: Dallas(ish).

Re: first night, first timer

Post by palerider » Sat Feb 20, 2016 9:09 pm

Julie wrote: Don't try to adapt to the machine's rhythm in any way - it's supposed to adapt to your breathing and respond by raising pressure if necessary, but you're not expected to do anything otherwise.
that's a very good point, the machine *has no rhythm*, it just supplies constant air pressure.

many people who are new to it think that there's something the machine is trying to get them to do, but it's not.

_________________
Mask: Bleep DreamPort CPAP Mask Solution
Additional Comments: S9 VPAP Auto
Get OSCAR

Accounts to put on the foe list: dataq1, clownbell, gearchange, lynninnj, mper!?, DreamDiver, Geer1, almostadoctor, sleepgeek, ajack, stom, mogy, D.H., They often post misleading, timewasting stuff.

User avatar
dontknowhowtodeal
Posts: 17
Joined: Sat Feb 20, 2016 4:44 pm

Re: first night, first timer

Post by dontknowhowtodeal » Sat Feb 20, 2016 10:20 pm

If i unplug my machine to move it, will that cancel all of the settings? I did not set up my machine so I don't know what numbers were used

_________________
Mask
Additional Comments: amara view minimal contact full face mask, ResMed Airsense Autoset 10

User avatar
Wulfman...
Posts: 6688
Joined: Mon Sep 01, 2014 6:41 pm
Location: Nearest fishing spot

Re: first night, first timer

Post by Wulfman... » Sat Feb 20, 2016 10:23 pm

dontknowhowtodeal wrote:If i unplug my machine to move it, will that cancel all of the settings? I did not set up my machine so I don't know what numbers were used
Nope! Everything will be fine.


Den

.
(5) REMstar Autos w/C-Flex & (6) REMstar Pro 2 CPAPs w/C-Flex - Pressure Setting = 14 cm.
"Passover" Humidification - ResMed Ultra Mirage FF - Encore Pro w/Card Reader & MyEncore software - Chiroflow pillow
User since 05/14/05

User avatar
Wulfman...
Posts: 6688
Joined: Mon Sep 01, 2014 6:41 pm
Location: Nearest fishing spot

Re: first night, first timer

Post by Wulfman... » Sat Feb 20, 2016 10:25 pm

As a side note, you should actually go through the setup menus and copy down on paper what all the original/existing settings are. That way you'll have a reference point for them and it'll give you experience and practice going through the menus.


Den

.
(5) REMstar Autos w/C-Flex & (6) REMstar Pro 2 CPAPs w/C-Flex - Pressure Setting = 14 cm.
"Passover" Humidification - ResMed Ultra Mirage FF - Encore Pro w/Card Reader & MyEncore software - Chiroflow pillow
User since 05/14/05

User avatar
jonny515
Posts: 221
Joined: Sun Dec 20, 2015 2:41 pm
Location: New Mexico

Re: first night, first timer

Post by jonny515 » Sat Feb 20, 2016 11:10 pm

You sound like you are doing better than I am at week 2. I understand it can take a month or even longer to get used to. It's more uncommon to get used to it really quickly, my understanding anyway.

User avatar
dontknowhowtodeal
Posts: 17
Joined: Sat Feb 20, 2016 4:44 pm

Re: first night, first timer

Post by dontknowhowtodeal » Sun Feb 21, 2016 12:16 am

johnny515, I have only used the machine once. But i had a lot of reactions, and now am trying to figure out how to change the temperature

_________________
Mask
Additional Comments: amara view minimal contact full face mask, ResMed Airsense Autoset 10

otrpu
Posts: 88
Joined: Fri Jan 11, 2008 8:50 pm
Location: Colorado

Re: first night, first timer

Post by otrpu » Sun Feb 21, 2016 12:17 am

You might like the Hybrid FFM better than what you have. It's still a FFM, but has nose pillows and a much smaller mouth area to seal. Kit comes with all three sizes of cushions and nasal pillows. Link is in my equip listing.
Cheers,
otrpu

_________________
Machine: ResMed AirSense™ 10 AutoSet™ CPAP Machine with HumidAir™ Heated Humidifier
Additional Comments: ResMed Oxi, ClimateLine w/sock

User avatar
dontknowhowtodeal
Posts: 17
Joined: Sat Feb 20, 2016 4:44 pm

Re: first night, first timer

Post by dontknowhowtodeal » Mon Feb 22, 2016 7:04 pm

I checked my settings and discovered that the tube temperature was set at auto, which it looks like could go as high as 85 or 90. What would be the suggested temp to try? I lowered it to 78

_________________
Mask
Additional Comments: amara view minimal contact full face mask, ResMed Airsense Autoset 10

User avatar
OkyDoky
Posts: 2870
Joined: Mon Aug 25, 2014 5:18 pm

Re: first night, first timer

Post by OkyDoky » Mon Feb 22, 2016 7:17 pm

dontknowhowtodeal wrote:I checked my settings and discovered that the tube temperature was set at auto, which it looks like could go as high as 85 or 90. What would be the suggested temp to try? I lowered it to 78
You just have to try different settings and see what feels good to you. Everyone has their preferences and what works for them.
ResMed Aircurve 10 VAUTO EPAP 11 IPAP 15 / P10 pillows mask / Sleepyhead Software / Back up & travel machine Respironics 760