newbie with questions

General Discussion on any topic relating to CPAP and/or Sleep Apnea.
User avatar
Spidermonkey
Posts: 16
Joined: Thu Jan 18, 2007 6:14 pm
Location: Bronxville, NY

newbie with questions

Post by Spidermonkey » Thu Jan 18, 2007 6:39 pm

Hello all,

I started reading this forum and gathering information as soon as I was diagnosed with severe OSA, before my titration study was even conducted. I've been on CPAP for about three weeks, and could use some advice.

First of all, after two titration studies the lab was unable to determine optimum pressure. I slept so badly that I never got into the necessary sleep stage, and my events sort of jumped around all over the place at different pressures. My doctor decided to set my machine at a relatively low pressure (7) because I did ok, things jumped all over at mid-level pressures, and at higher pressures I got worse. I'm wondering if others have had this experience.

So, I'm worried about whether my CPAP is set at the right pressure for me. From my reading, I am under the impression that my Remstar M-Series Auto with C-flex is an auto-pap capable machine. The person I spoke to at my DME said it is not. Who is correct? If it is APAP capable, I am going to ask my doctor to enable it.

I started out with a SNAPP nasal pillow mask because I detested the mask used at the sleep study. It was ok but far from great. At the second titration study, the lab gave me a ComfortLite 2 with direct seal. I find it a huge improvement. The only problem is, I developed a sore spot at the inside/outside juncture of one nostril while using the SNAPP and, though it's a bit better, it is not going away because I am still using a nasal interface. I tried using the mask that comes with the Comfortlite2 to give it a chance to heal, but I CANNOT sleep with a mask. Any suggestions? Any magic potions?

By the way, my username is Spidermonkey because my son said that was what I looked like with my headgear on.....

Susan


User avatar
oldgearhead
Posts: 1243
Joined: Thu Mar 30, 2006 9:53 am
Location: Indy

Post by oldgearhead » Thu Jan 18, 2007 6:58 pm

Lots going on here. I can answer one question:

The M series Auto IS capable of auto titration. I expect the set-up code
is AFLE just like the older unit.

I also would guess that if you hold down the < & > keys, then plug the
unit in the power socket until you hear two beeps, then release the two keys
the "M" will go right into its set-up mode, just like the older unit.

When you set up an APAP you must enter both a minimum and a maximum
pressure. I good starting point for you might be 6 min and 11 max.
However, I am not a medical professional, so I know nothing..

+ Aussie heated hose.
....................................................................

People have more fun than anybody..

User avatar
Spidermonkey
Posts: 16
Joined: Thu Jan 18, 2007 6:14 pm
Location: Bronxville, NY

Post by Spidermonkey » Thu Jan 18, 2007 7:17 pm

Thank you thank you thank you

Your instructions worked, and I was also able to turn on the AHI index and leak notification. Funny the things that can make you happy.

Susan


snoregirl
Posts: 1318
Joined: Fri Apr 07, 2006 3:36 pm

Post by snoregirl » Thu Jan 18, 2007 8:08 pm

Good advice.

User avatar
bdp522
Posts: 3378
Joined: Tue Jun 27, 2006 5:13 pm

Post by bdp522 » Thu Jan 18, 2007 9:26 pm

You could use a little neosporin on the sore. If it's just irritated try ary gel.

Brenda