Phillips Resp. System One Blower Issues. Repair Ideas? Help.
Phillips Resp. System One Blower Issues. Repair Ideas? Help.
Hello, have a 'just out of warranty' system one that is exhibiting unusual blower issues before putting on the mask. It goes at a normal speed for a few moments then drops down then comes up and drops down etc. I put on the mask but concerned the air pressure might not be enough even though I can't feel a difference. Should this be sent in for repair somewhere or is it as simple as taking it a part and replacing the fan or some key components? Any help, experience or recommendations are appreciated.
Re: Phillips Resp. System One Blower Issues. Repair Ideas? Help.
How does it behave if you put on the mask and then turn it on?
_________________
Machine: DreamStation CPAP Machine |
Mask: Amara View Full Face CPAP Mask with Headgear |
Humidifier: DreamStation Heated Humidifier |
- Sir NoddinOff
- Posts: 4190
- Joined: Mon May 14, 2012 5:30 pm
- Location: California
Re: Phillips Resp. System One Blower Issues. Repair Ideas? Help.
_________________
Mask: AirFit™ F10 Full Face Mask with Headgear |
Additional Comments: Sleepyhead software v.0.9.8.1 Open GL and Encore Pro v2.2. |
I like my ResMed AirFit F10 FFM - reasonably low leaks for my ASV therapy. I'm currently using a PR S1 AutoSV 960P Advanced. I also keep a ResMed S9 Adapt as backup. I use a heated Hibernite hose. Still rockin' with Win 7 by using GWX to stop Win 10.
Re: Phillips Resp. System One Blower Issues. Repair Ideas? Help.
Sort of hard to tell if the air pressure falls when the mask is on. When the mask is off it's like a yoyo. Until recently, everything was running fine. Is the blower the issue on these? Thanks for the repair link.
- Wulfman...
- Posts: 6688
- Joined: Mon Sep 01, 2014 6:41 pm
- Location: Nearest fishing spot
Re: Phillips Resp. System One Blower Issues. Repair Ideas? Help.
Probably not. Could be a sensor or internal hose connection.Team5D wrote:Sort of hard to tell if the air pressure falls when the mask is on. When the mask is off it's like a yoyo. Until recently, everything was running fine. Is the blower the issue on these? Thanks for the repair link.
What "Series" is it? 50 or 60?
By the way, when you have the mask off, it's hard telling how it's going to act.
You can do a "homemade manometer" test with a bucket of water and a ruler marked in centimeters to test the output.
Go up to the Search line and put in "homemade manometer" and start reading. Look for the one by the forum member "tomjax". I've also referenced it many times over the years, too.
Den
.
(5) REMstar Autos w/C-Flex & (6) REMstar Pro 2 CPAPs w/C-Flex - Pressure Setting = 14 cm.
"Passover" Humidification - ResMed Ultra Mirage FF - Encore Pro w/Card Reader & MyEncore software - Chiroflow pillow
User since 05/14/05
"Passover" Humidification - ResMed Ultra Mirage FF - Encore Pro w/Card Reader & MyEncore software - Chiroflow pillow
User since 05/14/05
- grayghost4
- Posts: 1554
- Joined: Wed Aug 20, 2014 6:52 pm
- Location: Norther Illinois
- Contact:
Re: Phillips Resp. System One Blower Issues. Repair Ideas? Help.
If you're not part of the solution you're just scumming up the bottom of the beaker!
Get the Clinicians manual here : http://apneaboard.com/adjust-cpap-press ... tup-manual
Get the Clinicians manual here : http://apneaboard.com/adjust-cpap-press ... tup-manual
- Sir NoddinOff
- Posts: 4190
- Joined: Mon May 14, 2012 5:30 pm
- Location: California
Re: Phillips Resp. System One Blower Issues. Repair Ideas? Help.
Oh yeah, that's one of my favs too.
_________________
Mask: AirFit™ F10 Full Face Mask with Headgear |
Additional Comments: Sleepyhead software v.0.9.8.1 Open GL and Encore Pro v2.2. |
I like my ResMed AirFit F10 FFM - reasonably low leaks for my ASV therapy. I'm currently using a PR S1 AutoSV 960P Advanced. I also keep a ResMed S9 Adapt as backup. I use a heated Hibernite hose. Still rockin' with Win 7 by using GWX to stop Win 10.
Re: Phillips Resp. System One Blower Issues. Repair Ideas? Help.
When not wearing the mask, shouldn't "unusual blower issues" be expected?Team5D wrote: exhibiting unusual blower issues before putting on the mask