General Discussion on any topic relating to CPAP and/or Sleep Apnea.
-
i_am_jim
- Posts: 38
- Joined: Wed Oct 26, 2005 2:14 pm
Post
by i_am_jim » Sun Oct 30, 2005 9:22 am
I can't relate to this discussion. The "hood" opens on my 3i humidifier and I remove the water chamber. I pour out any remaining water each morning and replace the chamber, leaving the hood up. By evening any water droplets have evaporated.
I remove it at night and hold it over the basin to fill it.
Last edited by
i_am_jim on Sun Oct 30, 2005 4:20 pm, edited 1 time in total.
ResMed airsense10 w/integrated Humidifier
ResMed Mirage Swift Lt Pillow System

-
Severeena
- Posts: 821
- Joined: Sat Mar 26, 2005 3:54 pm
- Location: 907 Main Street, Union Grove, WI 53182
-
Contact:
Post
by Severeena » Sun Oct 30, 2005 2:59 pm
I remove the water resivior from the machine. I then fill my tank where the hose attaches to the water resivoir.
The more you take the plastic pieces apart the more you have problems with the resivior sealing properly.
_________________
Mask | |
 |
Sharon
Trust in the Lord with all thine heart and lean not until thine own understanding ..... Proverbs 3:5-
Not all Masks work for everyone. Each Person is Different.
-
dsm
- Posts: 6996
- Joined: Mon Jun 20, 2005 6:53 am
- Location: Near the coast.
Post
by dsm » Sun Oct 30, 2005 3:30 pm
lindas88 wrote:
<snip>
The 2i looks more prone to problems if pulled apart repeatedly.
dsm....what makes you think this? Do you think the problem is with the rubber piece? Or maybe the clips at the side?
<snip>
Removing & replacing that seal is one of the problems. The effort to pull this unit apart can be another problem. They are not exactly easy to pull apart & it is not hard to see people dropping one or both halves while doing so. But that said, It is not enough to put me off owning one, just that I would be extra carefull in the way I handle it & the times I pull it apart for a full clean.
Cheers
DSM
_________________
CPAPopedia Keywords Contained In This Post (Click For Definition):
seal,
clean
xPAP and Quattro std mask (plus a pad-a-cheek anti-leak strap)
-
inacpapfog
- Posts: 538
- Joined: Tue Nov 16, 2004 6:03 pm
- Location: SC
Post
by inacpapfog » Mon Oct 31, 2005 5:42 pm
You're exactly right, dsm! I make it a point to be extra careful when handling my humidifier! Those plastic clips would oh so easy to break, as would the chambers themselves! Even when pulling off/ replacing the rubber seal for washing, I take time to be sure its seated correctly before trying to clip the unit shut. So far, in a years time, no problems!
I was in a cpap fog until I came here to learn!
-
lindas88
- Posts: 321
- Joined: Sat Jul 09, 2005 12:44 pm
- Location: New Brunswick, Canada
-
Contact:
Post
by lindas88 » Tue Nov 01, 2005 3:22 pm
i_am_jim wrote:I can't relate to this discussion. The "hood" opens on my 3i humidifier and I remove the water chamber. I pour out any remaining water each morning and replace the chamber, leaving the hood up. By evening any water droplets have evaporated.
I remove it at night and hold it over the basin to fill it.
The 3i humidifier looks much easier to use....
*** Linda ***