There is a newer version of Sleepyhead (0.8.7) and this is in the update features: "What's New? You can now Shift+Left Click on a day in an overview graph, and it will jump to that day in Daily tab. New calendar navigation bar allows easy hiding the calendar to get more room. (Relative) AHI is displ...

As far as I know these are the codes for CPAP and BiPAP machines.
E0601 Continuous airway pressure (CPAP) device (e.g. smart CPAP, auto CPAP, CPAP)
E0470 Bilevel
E0471 Bilevel with backup rate

Yours seems to be E0601 as far as I can tell.
Good Luck!

Here is what a complete one should look like. Bottom half and top half together. The black almost diagonal line is the division between the halves.



Good Luck!

My Remstar is showing a code e-24 and does not work, do I have to send it off to repair it????????????? Sorry about furthering the hijack but the code E-24 says: E-24 ERR_UNRECOGNIZED_CAL_VERSION_BY_SW •Improper calibration •Defective FLASH chip •Recalibrate •Replace Main PCA Doesn't sound too good...

Unfortunately I am not aware of a list of error codes for Resmed units. Instead they advise calling their service.
This number is for Customer service, I believe, and perhaps they can halp you. 800-424-0737.

Good Luck!
Ron

I am curious as well. When I got my machine my pressure was at the prescribed 12 CmH2O. The C=Flex or EPR was at 3. My inspiration pressure was the same as my prescribed pressure. My machine is a Respironics and I know that the C-Clex is not a 1 for each 1 cmH20 but I think the basics are the same. ...

There are several on EBAY now for less than 30.00.

http://www.ebay.com/sch/i.html?_nkw=res ... m270.l1313

Good Luck!

... The only difference I can see is an added option to turn on "Silent Mode", but I don't even know what this does... WHOA! Hold on.. SILENT MODE?!? Could this be Respironics addressing one of the big complaints from its customers? Please check this: Turn silent mode on, and then see if the machin...

Janknitz is correct, at least in my case. The DME is billing total list price but the insurance is only allowing so much. It is not as cheap as CPAP.Com but a lot better than list. That would change your calculations. Also, I like the fact that it is "yours" much quicker if you were to purchase outr...

Version 0.8.6 of Sleepyhead allows you to set an intentional leak value so it gets removed from the graph. It can be set in File > Preferences and under the CPAP/Visual tab which should be the default. If you set an intentional leak value then the graphs show just leaks above that value. I believe 2...

Did you see how he tested the pressure? The reason I ask is I have a manometer that measures air pressure, but just not sure where & how the hook it up to test. Do they seal the end? Do they just attach the mask and have a Tee connector coming off that allows air to come out to be measured. Just cu...

bbsargent, Welcome to the board. Here are a couple of previous threads about that topic. http://www.cpaptalk.com/viewtopic.php?f=1&t=69172 http://www.cpaptalk.com/viewtopic.php?f=1&t=69037 An wasy way to get used to it is put it on early and read or watch TV, then you are consciously getting used to...

If you haven't seen this active thread, it has some good suggestions as well, especially the last one by Chunkyfrog.
viewtopic/t69305/Annoying-face-fart-issue.html

Good Luck!

Is your face sweating under the masK? It sounds like either oils or something is interfering with the seal.
Have you tried a mask liner like from PadACheek? http://www.padacheek.com/PAC_Maskliners.html
There will be better suggestions I am sure, but Good Luck!

Here is another video.
Hope it helps.
http://www.resmed.com/us/products/swift ... s&sec=true

Good luck!