Page 7 of 13
Re: Updating the firmware on the PR System One machines
Posted: Wed Sep 19, 2012 8:57 am
by squid13
If you're able to do it yourself and the update goes South you got yourself an expensive paper weight. Sort of like flashing your BIOS in a computer.
Re: Updating the firmware on the PR System One machines
Posted: Wed Sep 19, 2012 9:56 pm
by JohnO
DiverCTHunter wrote:
So at this point, the following versions have been seen in the wild:
v.1.07 (could change time from GMT)
v.1.13
v.1.22
v.1.24
v.2.01
v.2.02
v.2.50
v.2.51
Realize too, the PR System 1 60 Series machines have different firmware as well. My 560 has version 3.02 software.
Re: Updating the firmware on the PR System One machines
Posted: Tue Sep 25, 2012 10:44 am
by johnthomasmacdonald
I miss the old black att phones that you could actually spin the dial, so i'm probably not a good choice for an early adaptor
Re: Updating the firmware on the PR System One machines
Posted: Wed Sep 26, 2012 2:07 pm
by DiverCTHunter
blakepro wrote:Just a heads up, if anyone ever figures out how to obtain one of these cables, they have just released a new firmware flasher on 09/11/2012 that brings machines up to version 2.53
PR System 1 Flash Upgrade Utility 2.53 09/11/2012
Philips Respironics System 1 Flash Upgrade Utility is used to upgrade devices with current software version 2.XX to software version 2.53
I can confirm that Respironics uses an RS-232 interface. The part number is 1074113 and can be found from several specialty medical-supply houses. -
http://www.medexsupply.com/product_info ... s_id=49693
Re: Updating the firmware on the PR System One machines
Posted: Wed Sep 26, 2012 11:00 pm
by DiverCTHunter
Here's the pinout:
1 Vref/DTR/DSR
2 open
3 TD
4 RD
5 open
6 open
7 GND
*Edit* Pin 1 is the wide contact on the right (conveniently marked "1"). Pin 7 is the wide contact on the left.
Re: Updating the firmware on the PR System One machines
Posted: Sat Sep 29, 2012 2:59 am
by deltadave
blakepro wrote:Just a heads up, if anyone ever figures out how to obtain one of these cables, they have just released a new firmware flasher on 09/11/2012 that brings machines up to version 2.53
PR System 1 Flash Upgrade Utility 2.53 09/11/2012
Philips Respironics System 1 Flash Upgrade Utility is used to upgrade devices with current software version 2.XX to software version 2.53
Keep in mind that only a 2.xx machine can be upgraded to 2.53.
If you have a 1.xx machine you can only flash to 1.24.
And again, we're only talking about PRS1s (note Topic Header).
Re: Updating the firmware on the PR System One machines
Posted: Tue Oct 09, 2012 2:54 pm
by DiverCTHunter
*Bump*
Going to be heading to my 1 year followup in a few weeks. I can get one of the RTs to give me the firmware update then, but I'd like to know if anyone has the release notes.
Re: Updating the firmware on the PR System One machines
Posted: Tue Oct 09, 2012 4:46 pm
by ChrisD
Wouldn't the RT who is giving you the update have access to the release notes?
Chris
Re: Updating the firmware on the PR System One machines
Posted: Tue Oct 09, 2012 5:43 pm
by chunkyfrog
An RT that can read; hmmm, how do you find one of those?
Re: Updating the firmware on the PR System One machines
Posted: Fri Oct 12, 2012 6:08 pm
by deltadave
chunkyfrog wrote:An RT that can read; hmmm, how do you find one of those?
The heck if I know!
Re: Updating the firmware on the PR System One machines
Posted: Tue Oct 16, 2012 12:29 pm
by accurate
Hi folks.
As we are prohibited from selling Respironics' parts to the public, we've decided to roll out this program on a trial basis.
Accurate Biomed Services Inc. is proud to announce a new service aimed at CPAP users that desire to have their equipment upgraded.
The manufacturer provides the following information:
Philips Respironics System One Firmware Upgrade
Firmware Upgrade Version 2.53 is for 2.XX model versions only. The version can be determined by looking at the serial number label at the bottom center.
Products Affected Are As Follows:
SYS. One Remstar
SYS. One Remstar Plus
SYS. One Remstar Auto
SYS. One BiPap Pro
SYS. One BiPap Auto
Information on new features of firmware upgrade:
HUMIDIFIER PREHEAT:
When using a humidifier, the device can now preheat the water tank for up to 30 minutes prior to starting therapy.
SILENT MODE:
You can disable the audible beep during power on, therapy start, therapy stop, mask fit check and humidifier preheat mode.
RAMP TIME
Enables you to modify the Ramp time setting in 5 minute increments. The range for this setting is 0 to 45 minutes.
Firmware Upgrade 2.50 For SYS. One Remstar Pro.
This firmware version impacts the Remstar Pro w/C-Flex+ by adding AutoIQ functionality. Devices with AutoIQ are capable of providing a two-phase therapy approach that is comprised of an Auto-Trial and an Auto-Check phase along with the above features.
You will receive a computerized calibration with printout, new filters, and a user manual insert along with the upgrade further explaining these features in more detail.
The cost of this service is $65.00 plus shipping.
If we get a lot of blow back from the manufacturer about this, we'll have to discontinue, but I've received some pm's expressing interest and we're going to try to take care of the people that are interested. It would be helpful if you could provide your prescription as we will want to set the cpap up for your specific settings. As always you can contact Accurate with any questions.
Re: Updating the firmware on the PR System One machines
Posted: Wed Oct 17, 2012 3:27 am
by deltadave
accurate wrote:Philips Respironics System One Firmware Upgrade
This firmware version impacts the Remstar Pro w/C-Flex+ by adding AutoIQ functionality. Devices with AutoIQ are capable of providing a two-phase therapy approach that is comprised of an Auto-Trial and an Auto-Check phase along with the above features.
As always you can contact Accurate with any questions.
Yeah I got one (give or take).
If you add AutoIQ to a machine don't you technically have to upgrade to the REMstar AutoIQ Top Enclosure? Are you including this part in your price?
Also, how's the shipping work?
TIA
Re: Updating the firmware on the PR System One machines
Posted: Wed Oct 17, 2012 3:41 am
by deltadave
OK, I hate to be a pain (j/k!), butt (get it?) in the features listed below:
accurate wrote:Philips Respironics System One Firmware Upgrade
Firmware Upgrade Version 2.53 is for 2.XX model versions only. The version can be determined by looking at the serial number label at the bottom center.
Information on new features of firmware upgrade:
HUMIDIFIER PREHEAT:
When using a humidifier, the device can now preheat the water tank for up to 30 minutes prior to starting therapy.
SILENT MODE:
You can disable the audible beep during power on, therapy start, therapy stop, mask fit check and humidifier preheat mode.
RAMP TIME
Enables you to modify the Ramp time setting in 5 minute increments. The range for this setting is 0 to 45 minutes.
Firmware Upgrade 2.50 For SYS. One Remstar Pro.
This firmware version impacts the Remstar Pro w/C-Flex+ by adding AutoIQ functionality. Devices with AutoIQ are capable of providing a two-phase therapy approach that is comprised of an Auto-Trial and an Auto-Check phase along with the above features.
are not they all features of 2.50? IOW, if a user has v.2.50, there is no point in upgrading to 2.53?
TIAA.
Re: Updating the firmware on the PR System One machines
Posted: Thu Oct 18, 2012 4:57 am
by deltadave
accurate wrote:As always you can contact Accurate with any questions.
Soooo.....?
Re: Updating the firmware on the PR System One machines
Posted: Thu Oct 18, 2012 8:31 am
by ChrisD
deltadave wrote:accurate wrote:As always you can contact Accurate with any questions.
Soooo.....?[/url]
He possibly meant contact him via their website:
http://www.acbio.com
Chris