Page 4 of 5

Posted: Sat Mar 26, 2005 9:20 pm
by rock and roll
Go back and reread your post, you decided the thread was not going in the direction you liked so you tried to intimidate it back to what pleased you. SG and others clearly felt your force but you don't fool me. You may post more than anyone else but that does not make you boss of the forum, that falls to Johnny as it's his list. To me you are just a busy body with too much time on his hands!

Posted: Sat Mar 26, 2005 9:44 pm
by wading thru the muck!
I wrote:Besides, this thread was about the machine and not the mask. If when asked what could be better about the machine, the answer given is it's all about the mask, then we won't get better machines. Leave the mask comments for the mask thread.
The above is my exact quote. I see no intimidation. You are the one using the vulgar language and Nazi references. It's too bad you need to bring this kind of abusive language to the forum. I, for one, see no value in it. Once again you choose to insult my contribution to the forum by claiming I"m a busy body with too much time on my hands. That is as far from the truth as you could know. Please keep your comments relevant to the forum and refrain from refering to me using such inflamatory terms.

Posted: Sat Mar 26, 2005 9:56 pm
by rock and roll
You do not ask. You demand. I don't take commands from you. Read the few posts from others just after your post and read where they said don't be mad, and apologised for not being agreeable to your mood swing.

Muck, we have been through this,before. You seem to have a sense of ownership with this forum just because you post so much. I accepted your apology (after much negotiating on our part off forum) once before where you admited to being a hothead. Again, if you can acknowlege where you again barked, I will overlook. But I feel YOU are the one wrong here and I feel that you interfere to much on this forum and are therefore a detriment.

Posted: Sun Mar 27, 2005 2:21 pm
by Thomas
Since I got my AutoSet Spirit I have discovered the invaluable feature of having my AHI readings immediately available to me. Now I know that someting isn't working right, and am on a quest to find out what it is. Without this feature, there was no way for me to know something has been wrong with my cpap treatment for a long time. Since I also have an underactive thyroid, which causes similar symptoms, I thought that was the culprit. So having a readout on the machine with critcal info is extremely important to me now as well as the downloadable info.

Tom

Posted: Thu Mar 31, 2005 3:41 pm
by wading thru the muck!
TrippHammer (TAS) wrote:So anyone out there know of a Bi-level that will run on 12 VDC and a low current draw? I am a river rafter and am planning to do some trips (Desolation Canyon, Main Salmon and others) that will be at least 7 nights long or longer. Am hoping that somewhere out there is a manufacturer that will recognize the need to allow folks like myself to continue our outdoor activities. What I really am dreaming of is a waterproof (to survive the class IV and V rapids), low voltage, low current draw, bi-level machine that automatically adjusts for altitude changes. Am I asking to much? Take Care
Here's a request for a mchine with a combination of unique features from a poster on TAS

Posted: Thu Mar 31, 2005 5:13 pm
by chrisp
The PB 425 operates from 12V directly no inverters needed. Just the $7 cable from radio shack. It is similar to the PB420. That has a current draw of about .75 amps. Might check it out.



Chris

Posted: Thu Mar 31, 2005 5:38 pm
by wading thru the muck!
Chris,

Is it waterproof?

Can you repeatedly submurge it while whitewater rafting?

Posted: Thu Mar 31, 2005 5:42 pm
by chrisp
Buy one and give it a try. The resmed spirit can ingest water and survive . The PB isnt as durable. Just invest in a good waterproof bag and go for it. Dont forget the 57 pound battery . Mine lasted over 2 weeks. You might try 1 of these http://www.pelican-case.com/


Posted: Thu Mar 31, 2005 8:19 pm
by rock and roll
Go to WalMart and buy a watertight tack box, I have one that I fish and hunt with and I have taken it in the water snorkeling and it had done fine. A battery would fit in it fine, even have big ones the whole CPAP would fit into. Cost of it is $14.99.

Re: Most Important CPAP Feature/Attribute

Posted: Mon Jan 06, 2014 11:05 am
by MeToo
More effective interpretation and response to breathing disruptions.

Re: Most Important CPAP Feature/Attribute

Posted: Mon Jan 06, 2014 11:45 am
by RestedRebel
My machine is small and quiet, which allows me to travel with it. It is comfortable, my nasal pillows give me the air I need, and I've never felt better. I guess I'd say the most important things to me are: comfort, quiet, and portability. It's impossible for me to list just one attribute.

Re: Most Important CPAP Feature/Attribute

Posted: Mon Jan 06, 2014 2:41 pm
by OhHelpMe
Most Important CPAP Feature/Attribute
Blows air?

Re: Most Important CPAP Feature/Attribute

Posted: Thu Aug 21, 2014 9:03 am
by Daydream Believer
Breathability - but that includes fast response in pressure changes, recognizing pressure relief needs and being flexible between auto-adjusting and hard-set options.

I'd love to have some built-in options for aromatherapy (I'm still working on finding some that work for me) and anything that might help us overcome congestion during a cold. The humidifier is just one piece of that puzzle.

Another possible improvement... An optional container that holds more distiller water and keeps the reservoir filled without having to worry that it runs dry overnight. Yes, the reservoir still needs to be cleaned on schedule - but how many of us forget to check the water level till we're settled into bed? This could make the process easier for those of us who have a hard time lifting the gallon jug every few days,too.

Re: Most Important CPAP Feature/Attribute

Posted: Thu Aug 21, 2014 8:27 pm
by chunkyfrog
Smaller containers are easier to handle for those with a tremor, too.

Re: Most Important CPAP Feature/Attribute

Posted: Thu Aug 21, 2014 8:39 pm
by bwexler
All of the above is a good place to start.

Hopefully these prompt responses will make the cut before final design decisions are made on the new machines.