The Ipap/Epap pressure values go up and down through the night, which is normal. THey reach periodically the max set values ( in my case 14-18), but when they do there are no AHI's recorded on the graph on the corresponding timeline. I am just curious. Normally I would expect pressure peaking when the machine senses a decrease in the air flow due to a narrowing or obstruction of the airway . In other words, I would expect to see either an H or a an OA in the the event flag graphic. Does it mean that the machine did sense a decrease ( or an obstruction) in the air flow, but the pressure increase restored the air flow too quickly for an AHI to be recorded?
Thanks
Ittiandro
Max Ipap/epap values reached but no AHI's recorded
Re: Max Ipap/epap values reached but no AHI's recorded
These auto adjusting machines will also increase the pressure when it senses flow limitations and/or snoring.
It's not just about the OAs and hyponeas.
It's not just about the OAs and hyponeas.
_________________
Machine: AirCurve™ 10 VAuto BiLevel Machine with HumidAir™ Heated Humidifier |
Additional Comments: Mask Bleep Eclipse https://bleepsleep.com/the-eclipse/ |
I may have to RISE but I refuse to SHINE.
If you want to try the Eclipse mask and want a special promo code to get a little off the price...send me a private message.
If you want to try the Eclipse mask and want a special promo code to get a little off the price...send me a private message.
Re: Max Ipap/epap values reached but no AHI's recorded
And it's worth adding to Pugsy's reply:
The reason the auto machines respond to flow limitations and snoring is to prevent apneas and hypopneas from happening in the first place. Flow limitations and snoring both indicate the airway is in some danger of collapsing, so the machine increases the pressure in order to make it more difficult for the airway to collapse and cause an apena or hypopnea event to occur.
The reason the auto machines respond to flow limitations and snoring is to prevent apneas and hypopneas from happening in the first place. Flow limitations and snoring both indicate the airway is in some danger of collapsing, so the machine increases the pressure in order to make it more difficult for the airway to collapse and cause an apena or hypopnea event to occur.
_________________
Machine: AirCurve™ 10 VAuto BiLevel Machine with HumidAir™ Heated Humidifier |
Mask: Swift™ FX Nasal Pillow CPAP Mask with Headgear |
Humidifier: DreamStation Heated Humidifier |
Additional Comments: Also use a P10 mask |
Joined as robysue on 9/18/10. Forgot my password & the email I used was on a machine that has long since died & gone to computer heaven.
Correct number of posts is 7250 as robysue + what I have as robysue1
Profile pic: Frozen Niagara Falls
Correct number of posts is 7250 as robysue + what I have as robysue1
Profile pic: Frozen Niagara Falls
Re: Max Ipap/epap values reached but no AHI's recorded
Thanks
You are absolutely right. Looking at the graphs, I see that these pressure spikes correspond to snoring and/or FL events of about 0.30, Usually my FL readings are about 0.10-0.15, though, but this doesn't bother me, as long as my AHI's keep in the 0.30-0.80 range, as they usually do.
Also, I guess that I can't get yhe FL down to 0 because my upper airway, the doctor found, is narrower than the average person, which impedes a fuller flow of air.
I don't feel it, because I'm physically active and I run, but the machine picks it up when asleep.
My doctore had originally set the pressure settings to 8-15 cmH2O . My AHI's had already dramatically decreased to well under 5 since I started the CPAP therapytwo years ago, but I wanted to see if I could bring them further down, by increasung the min EPAP setting from 8 to around 14., while keeping the IPAP setting to around 18.
It worked, because the AHI's consistently dropped to under 1, keeping at an average of approximately 0.60, sometimes even 0, albeit rarely.
Ittiandro
- ChicagoGranny
- Posts: 14463
- Joined: Sun Jan 29, 2012 1:43 pm
- Location: USA