CPAPtalk.com

Thanks. I wasn’t sure if it was the new machine or what. I have an admin card it in now.

What size and card should I use? I have an 8 gig but I threw a 60 gig in there.

Gerryk wrote: ↑

Fri Apr 05, 2019 2:48 pm

Thanks. I wasn’t sure if it was the new machine or what. I have an admin card it in now.

What size and card should I use? I have an 8 gig but I threw a 60 gig in there.

I would pop the 8gig card in there

Two is enough.

Thanks, I can put the bigger one to use elsewhere.

When ResMed included an SD card, I think they were 2gb

Here is the data from last night. I woke up around 1:30 at the time of the first major leak. I could not get the new mask to seal and grabbed my old quattro ff mask and went back to sleep. I didn't wake up for the other leaks until the leak around 6:30. I got an email from my DME to call and come in because of the large leak. I will go in and try and adjust the mask but the funny part is I sleep for a few hours before the leaks begin and can't correct them. If this mask doesn't work out, they have one other new mask that is not as big as the quattro that I can try.

Please redo your screenshot as per the example in my signature below.

I did format it the way it says in your link. What do you want differently?

If you have the pressure chart, you don't need the mask pressure. We like to see one, or the other, not both. Also, do away with the pie chart. Looking at what you posted, I recommend you raise your minimum pressure to 11 and set your max to 20 and see where the machine wants to go. Your machine is reacting to events, going up, then dropping back down. Another events drives it up, then it goes back down and repeats this over and over all night. Once you raise your minimum pressure, your maximum may never go over 15, but until you raise the minimum there is no way of telling if it will or not.

Gerryk wrote: ↑

Sat Apr 06, 2019 10:42 am

I did format it the way it says in your link. What do you want differently?

The example in my link is this:



Yours is:



See the difference?

Increase the depth of the flow chart

I don't know how to and can't figure out how to resize any of this. I can not get the left side resized or the left of the right side so it can be read. Thanks but I am done trying.

Gerryk wrote: ↑

Sun Apr 07, 2019 9:31 am

I don't know how to and can't figure out how to resize any of this. I can not get the left side resized or the left of the right side so it can be read. Thanks but I am done trying.

from http://www.apneaboard.com/wiki/index.ph ... SleepyHead

Tricks for moving around SH and changing the appearance of the SH windows
Cursor left and right keys scrolls the highlighted box. If the calendar is highlighted, these keys will move the Daily Detailed data backward or forward by one day at a time.
Right clicking on, and then dragging the currently selected highlight in the Event Table allows you to easily slide the current selected time "window" over the whole period.
Right clicking on, and dragging any graph other than the Events Table will act as if you are picking it up and panning it left or right.
Double clicking on a graph's title text area pins or unpins any graph. Pinned graphs always remain visible on screen, up the top. Your graph pins are persistent.
Clicking on graph title text and dragging allows you to reorder the graphs, but pinned graphs will always be on top. Pinned graphs can be reordered amongst themselves in this same way.
Clicking on the date panel above the Daily Detail calendar toggles the calendar on/off to quickly give you more room in the Left Sidebar of the Daily Data for the statistical data
F8 key quickly toggles the right navigation panel to give you more graph room.
You can drag the vertical sizer line that is between the left panel and graph area all the way to the left, allowing you to get full screen graphs.
If you want to view only ONE of the Daily graphs or ONE of the Overview graphs, you can minimize all the graphs with the down arrow button next to the right side drop down in the bottom panel, then turn back on the graph you want to look at in the drop down menu in the bottom left corner. To make all the graphs visible again, click the arrows next to that drop down menu box twice.
The "Reset" button down the bottom panel of the graph area restores all graphs to uniform sizing.
You can click on the colored event names in the Daily Details panel to jump to them highlighted in the Events tab
You can click on the duration shown in the CPAP Sessions to highlight just that session.
Clicking on the an entry in the Prescription Changes list in the Statistics page will jump to Overview and select that date range.
Tooltip durations can be altered in the Appearance Preferences. If you find them annoying drag it all or most of the way to the left.
Shift-click on a date in the Overview screen and SH takes you to that date in Daily Data view.


from wiki/index.php/Sleepyhead:Organize

Adjusting height of graphs
You should also adjust the height of the graphs by pointing your mouse at the border of a graph and then moving the mouse up or down.

hope this helps!

Thanks. Zonker. I had figured most of it out but I cant figure anything on the left side out and can not resize the text that is the title on the right.

Gerryk wrote: ↑

Sun Apr 07, 2019 6:58 pm

Thanks. Zonker. I had figured most of it out but I cant figure anything on the left side out and can not resize the text that is the title on the right.

i'm not sure what you are saying. seems to me, and i may be wrong, that if you make the individual graphs bigger, it should make the rest bigger.

try doing as the i showed above then do another attachment here.