CPAP Hours Reset

Bought A Used REMstar Pro with c-flex model number 1005961 and I need to reset the usage hours to zero. I also need to get the REMstar Pro Smart card where would I get one, also need a hose.

JMCCLAIN007 wrote:Bought A Used REMstar Pro with c-flex model number 1005961 and I need to reset the usage hours to zero. I also need to get the REMstar Pro Smart card where would I get one, also need a hose.

If you go up to the Search line and put in the model number "1005961" you'll see lots of links.

You really don't "need" a smart card because that machine is not data-capable. It preceded the Pro 2 (which I use) and is pretty much the same as a "Plus" model......also no data.

However, the cards can be purchased at CPAP.COM.

Den
.


To clear the User hours: Push the Heat or Ramp button to erase (when in setup mode) (referenced below)

Here's the instructions to get into the setup:

REMstar Pro 2 Setup

When in the Setup Menu, the humidifier ^ and ramp v buttons operate as up and down keys to change the settings, the left/right user buttons < > allow you to go to the previous/next question or setting, and the pressure start/stop button is used to exit the Setup Menu. Holding the humidifier or ramp buttons down will cause the values to change more quickly.

To enter the Therapy Setup Menu, hold the two top user buttons < > down while plugging in the power cord.
Continue holding the buttons down until the REMstar Pro 2 with C-Flex beeps.

Note: The word "setup" will appear on all of the screens indicating that you are in the Therapy Setup Menu.
If you press the Pressure start/stop button, you will exit the Setup Menu.

a. Compliance hours: (recommend leaving alone) Select next setting with >
(To clear the User hours: Push the Heat or Ramp button to erase (when in setup mode)

b. Therapy mode: (CPAP or CFLE) select with ^ or v Select next setting with >

c. CPAP pressure setting: Select with ^ or v Select next setting with >

d. C-Flex mode (if you chose CFLE mode): Select setting 1, 2 or 3 with ^ Select next setting with >

e: Ramp time setting: Select with ^ or v (ramp time will be turned off with a setting of 0:00) Select next setting with >

f. Ramp pressure setting: Select with ^ or v Select next setting with >

g. Patient disconnect setting: 1 = on 0 = off Select with ^ or v Select next setting with >

h. Buttons lights setting: 1 = on 0 = off Select with ^ or v (Last setting. Use On/Off button to exit Setup)

.

Wulfman... wrote:

JMCCLAIN007 wrote:Bought A Used REMstar Pro with c-flex model number 1005961 and I need to reset the usage hours to zero. I also need to get the REMstar Pro Smart card where would I get one, also need a hose.

If you go up to the Search line and put in the model number "1005961" you'll see lots of links.

You really don't "need" a smart card because that machine is not data-capable. It preceded the Pro 2 (which I use) and is pretty much the same as a "Plus" model......also no data.

However, the cards can be purchased at CPAP.COM.

Den
.


To clear the User hours: Push the Heat or Ramp button to erase (when in setup mode) (referenced below)

Here's the instructions to get into the setup:

REMstar Pro 2 Setup

When in the Setup Menu, the humidifier ^ and ramp v buttons operate as up and down keys to change the settings, the left/right user buttons < > allow you to go to the previous/next question or setting, and the pressure start/stop button is used to exit the Setup Menu. Holding the humidifier or ramp buttons down will cause the values to change more quickly.

To enter the Therapy Setup Menu, hold the two top user buttons < > down while plugging in the power cord.
Continue holding the buttons down until the REMstar Pro 2 with C-Flex beeps.

Note: The word "setup" will appear on all of the screens indicating that you are in the Therapy Setup Menu.
If you press the Pressure start/stop button, you will exit the Setup Menu.

a. Compliance hours: (recommend leaving alone) Select next setting with >
(To clear the User hours: Push the Heat or Ramp button to erase (when in setup mode)

b. Therapy mode: (CPAP or CFLE) select with ^ or v Select next setting with >

c. CPAP pressure setting: Select with ^ or v Select next setting with >

d. C-Flex mode (if you chose CFLE mode): Select setting 1, 2 or 3 with ^ Select next setting with >

e: Ramp time setting: Select with ^ or v (ramp time will be turned off with a setting of 0:00) Select next setting with >

f. Ramp pressure setting: Select with ^ or v Select next setting with >

g. Patient disconnect setting: 1 = on 0 = off Select with ^ or v Select next setting with >

h. Buttons lights setting: 1 = on 0 = off Select with ^ or v (Last setting. Use On/Off button to exit Setup)

.

Thank You this helped alot got everything where I needed it, now to just get the hose and card