Can anyone tell me where i can order parts for a Phillips Respironics System One 560 Auto. Mine is four years old and has gotten noisey. I am competent to swap out the blower. I presume there are some seals that should be replaced between blower and humidifier as well. Will i need to do any kind of calibration after the repair?
Thanks,
Jim
PR 560 Replace blower and seals
4 posts
• Page 1 of 1
PR 560 Replace blower and seals
_________________
| Machine: ResMed AirSense™ 10 AutoSet™ CPAP Machine with HumidAir™ Heated Humidifier |
| Mask: AirFit™ P30i Nasal Pillow CPAP Mask with Headgear Starter Pack |
| Additional Comments: Heated Humidifer, Non-Heated tube, Oscar |
Resmed Airsense 10 Autoset, Swift FX nasal pillows mask
Re: PR 560 Replace blower and seals
You *might* be able to get parts from acbio.com... they do service the units.jim22 wrote: ↑Wed Apr 11, 2018 9:08 pmCan anyone tell me where i can order parts for a Phillips Respironics System One 560 Auto. Mine is four years old and has gotten noisey. I am competent to swap out the blower. I presume there are some seals that should be replaced between blower and humidifier as well. Will i need to do any kind of calibration after the repair?
Thanks,
Jim
Before you do that though, see if it's noisy with just the blower...(detach the humidifier)... if it's quiet, you might have lost one, or more of the seals in the humidifier... I think that cpap.com (and other retailers) sell a humidifier seal kit.
Get OSCAR
Accounts to put on the foe list: dataq1, clownbell, gearchange, lynninnj, mper!?, DreamDiver, Geer1, almostadoctor, sleepgeek, ajack, stom, mogy, D.H., They often post misleading, timewasting stuff.
Accounts to put on the foe list: dataq1, clownbell, gearchange, lynninnj, mper!?, DreamDiver, Geer1, almostadoctor, sleepgeek, ajack, stom, mogy, D.H., They often post misleading, timewasting stuff.
-
grayghost4
- Posts: 1554
- Joined: Wed Aug 20, 2014 6:52 pm
- Location: Norther Illinois
- Contact:
Re: PR 560 Replace blower and seals
this is a new 560 with power supple and case .... no humidifier
might be less than parts
https://sfbay.craigslist.org/eby/hab/d/ ... 63021.html
might be less than parts
https://sfbay.craigslist.org/eby/hab/d/ ... 63021.html
If you're not part of the solution you're just scumming up the bottom of the beaker!
Get the Clinicians manual here : http://apneaboard.com/adjust-cpap-press ... tup-manual
Get the Clinicians manual here : http://apneaboard.com/adjust-cpap-press ... tup-manual
Re: PR 560 Replace blower and seals
If you're going to do this, remember that you aren't married to this machine. You can buy a different machine. Remember to make sure it's an automatic like your current one.grayghost4 wrote: ↑Thu Apr 12, 2018 12:05 pmthis is a new 560 with power supple and case .... no humidifier
might be less than parts
https://sfbay.craigslist.org/eby/hab/d/ ... 63021.html
_________________
| Machine | Mask | |||
 |  | |||
| Additional Comments: Auto PAP; 13.5 cmH2O min - 20 cmH2O max | ||||
4 posts
• Page 1 of 1