boiling stuff

General Discussion on any topic relating to CPAP and/or Sleep Apnea.
drdrew
Posts: 70
Joined: Thu Aug 04, 2011 3:00 pm
Location: missouri
Contact:

boiling stuff

Post by drdrew » Fri Jan 20, 2012 9:22 am

okay i use the mirage liberty hybrid type mask. i got some replacement silicone about a month ago. i notice the older stuff not sealing as well. i read back on boiling the nasal pillows to revive them. i plan to do that. my question is about the mouthpiece silicone. could that be boiled too? would it help?

_________________
Mask: Mirage Liberty™ Full Face CPAP Mask with Nasal Pillows With Headgear
Additional Comments: will update equipment once its settled

User avatar
JohnBFisher
Posts: 3821
Joined: Wed Oct 14, 2009 6:33 am

Re: boiling stuff

Post by JohnBFisher » Fri Jan 20, 2012 11:02 am

Though I do not know, I am pretty certain that boiling the silicone of the mask would cause it to loose flexibility. It seems that it would essentially accelerate what happens when it is exposed to air and our faces over time.

But I have not tried this before, so do not know. But to let you know, I even checked the user guide for my mask and did not see any mention of how it would behave when exposed to high heat.

However, if you are thinking of sterilizing your mask, there are better ways to clean it than to boil (and possibly ruin) it. Simple soap, water and rinse will do a much better job without causing possible damage.

_________________
Mask: Quattro™ FX Full Face CPAP Mask with Headgear
Additional Comments: User of xPAP therapy for over 20 yrs. Resmed & Respironics ASV units with EEP=9cm-14cm H2O; PSmin=4cm H2O; PSmax=15cm H2O; Max=25cm H2O
"I get up. I walk. I fall down. Meanwhile, I keep dancing” from Rabbi Hillel
"I wish to paint in such a manner as if I were photographing dreams." from Zdzisław Beksiński

User avatar
Pugsy
Posts: 63872
Joined: Thu May 14, 2009 9:31 am
Location: Missouri, USA

Re: boiling stuff

Post by Pugsy » Fri Jan 20, 2012 11:20 am

I would only try the boiling thing if I had suitable replacements for whatever I am boiling... just in case boiling was a disaster.
I know several members have had good luck boiling nasal pillows. I am not so sure about the cushion in the mouthpiece though BUT if you have a replacement on hand and you have already deemed it unusable in current condition then there is nothing to lose because it likely would end up in the trash can anyway.

_________________
Machine: AirCurve™ 10 VAuto BiLevel Machine with HumidAir™ Heated Humidifier
Additional Comments: Mask Bleep Eclipse https://bleepsleep.com/the-eclipse/
I may have to RISE but I refuse to SHINE.

If you want to try the Eclipse mask and want a special promo code to get a little off the price...send me a private message.

User avatar
chunkyfrog
Posts: 34369
Joined: Mon Jul 12, 2010 5:10 pm
Location: Nebraska--I am sworn to keep the secret of this paradise.

Re: boiling stuff

Post by chunkyfrog » Fri Jan 20, 2012 12:41 pm

--And please let us know your results.

_________________
Mask: AirFit™ P10 For Her Nasal Pillow CPAP Mask with Headgear
Additional Comments: Airsense 10 Autoset for Her

User avatar
Kairosgrammy
Posts: 529
Joined: Mon Jan 02, 2012 8:13 am

Re: boiling stuff

Post by Kairosgrammy » Fri Jan 20, 2012 12:58 pm

I just don't think boiling your mask would be good even for the pillows. More likely they would melt I'd think. How long have you had the mask. You should be eligible for a new one if its in that rough a shape. If you are paying out of pocket, it might still be worth paying for a new one than trying to make an old one work.
drdrew wrote:okay i use the mirage liberty hybrid type mask. i got some replacement silicone about a month ago. i notice the older stuff not sealing as well. i read back on boiling the nasal pillows to revive them. i plan to do that. my question is about the mouthpiece silicone. could that be boiled too? would it help?

_________________
Mask: Swift™ FX For Her Nasal Pillow CPAP Mask with Headgear
Additional Comments: I'm starting to use sleepyhead.

User avatar
archangle
Posts: 9294
Joined: Sun Mar 27, 2011 11:55 am

Re: boiling stuff

Post by archangle » Fri Jan 20, 2012 4:28 pm

If you're ready to throw them away anyway, and have a spare, why not?

I'd boil the water, turn off the heat, let it sit for a minute or so and then drop the parts in. Or make something to hold the parts up from the bottom of the pot if you want to actually boil the parts.

_________________
Mask: Swift™ FX Nasal Pillow CPAP Mask with Headgear
Humidifier: S9™ Series H5i™ Heated Humidifier with Climate Control
Additional Comments: Also SleepyHead, PRS1 Auto, Respironics Auto M series, Legacy Auto, and Legacy Plus
Please enter your equipment in your profile so we can help you.
Click here for information on the most common alternative to CPAP.
If it's midnight and a DME tells you it's dark outside, go and check for yourself.

Useful Links.

ozze_dollar
Posts: 611
Joined: Wed Jun 08, 2011 5:20 pm
Location: Sydney,Australia

Re: boiling stuff

Post by ozze_dollar » Fri Jan 20, 2012 5:14 pm

I cant imagine boiling the cushion or pillows. I just wash while I am in the shower every moring with a pure soap and warm water then rinse.I think my cushions last longer than average.

User avatar
squid13
Posts: 2299
Joined: Fri Jul 15, 2011 3:47 pm
Location: Pensacola, FL

Re: boiling stuff

Post by squid13 » Fri Jan 20, 2012 5:18 pm

I've boiled my older Swift FX pillows with no problem to them, in fact I've been using them again. Seems to give them new life.

_________________
Machine: ResMed AirCurve 10 ASV Machine with Heated Humidifier
Mask: Evora Full Face Mask - Fitpack
Additional Comments: AirCurve 10 ASV, Oscar V1.0.1-r-1
US Navy Retired 1973,AirCurve 10 ASV, Mode: ASV Auto, Min EPAP: 7.2, Max EPAP: 15.0, Min PS:4.0, Max PS: 15.0, Mask ResMed Airtouch F20, Backup: (2) AirCurve 10 ASV

ozze_dollar
Posts: 611
Joined: Wed Jun 08, 2011 5:20 pm
Location: Sydney,Australia

Re: boiling stuff

Post by ozze_dollar » Fri Jan 20, 2012 7:16 pm

squid13 wrote:I've boiled my older Swift FX pillows with no problem to them, in fact I've been using them again. Seems to give them new life.
Well,there you go!

srodeman8

Re: boiling stuff

Post by srodeman8 » Fri Feb 17, 2012 10:19 am

Hi, the best thing to do is to get the water to boiling, then turn it off for a minute and then put in nasal pillows and leave in there for an hour or so, then shake to get all the remaining water out in the bathtub, and then dry out. Be sure it is COMPLETELY dry before using again. A blow dryer may be used. Don't boil, but do the next best thing. The tubing does change a bit, but is still usable - that's up to you, but the nasal pillows are fine. I do this when I start to get a nasal drip problem which happens periodically. I have found that the nasal drip goes away if I do this in conjunction with turning on the humidifier to 3 with less than an inch of water inside. I have a supply of nasal pillows and switch to a clean on each day.

User avatar
chunkyfrog
Posts: 34369
Joined: Mon Jul 12, 2010 5:10 pm
Location: Nebraska--I am sworn to keep the secret of this paradise.

Re: boiling stuff

Post by chunkyfrog » Fri Feb 17, 2012 10:27 am

My kids were both bottle babies--(back before breastfeeding was considered 'primitive')
Anyhow, I started out boiling their bottles and nipples (they were latex, then)
I stopped when I accidentally boiled the pot dry (probably had apnea then)
Do people sterilize baby stuff now?--the nipples are silicone--like our interface parts.
I might consider using the steamer, but it didn't work that well on edamame.

_________________
Mask: AirFit™ P10 For Her Nasal Pillow CPAP Mask with Headgear
Additional Comments: Airsense 10 Autoset for Her

DrBucky
Posts: 31
Joined: Mon Feb 06, 2012 7:41 pm

Re: boiling stuff

Post by DrBucky » Fri Feb 17, 2012 11:39 am

chunkyfrog wrote:My kids were both bottle babies--(back before breastfeeding was considered 'primitive')
Anyhow, I started out boiling their bottles and nipples (they were latex, then)
I stopped when I accidentally boiled the pot dry (probably had apnea then)
Do people sterilize baby stuff now?--the nipples are silicone--like our interface parts.
I might consider using the steamer, but it didn't work that well on edamame.
Rather than boiling you probably could get by with a microwaveable baby bottle sterilizer. Basically they are a covered dish that you put water at the bottom to steam everything. But yeah people still sterilize baby bottles.

Another option with baby bottles is to buy an insert (to hold the parts) and then just put them in the dishwasher (w/ or without other dishes) and make sure to turn on the "steam sanitize" setting. Most modern dishwashers have this feature.

_________________
Mask: Mirage™ SoftGel Nasal CPAP Mask with Headgear
Humidifier: S9™ Series H5i™ Heated Humidifier with Climate Control
Additional Comments: climate line hose rocks

Robespierre
Posts: 168
Joined: Sun Feb 15, 2009 3:36 pm
Location: S Colorado

Re: boiling stuff

Post by Robespierre » Fri Feb 17, 2012 11:56 am

As long as the silicone parts aren't resting on the bottom of the pot, you won't damage them with boiling water. Boiling water (100°C) should not be hot enough to damage the silicone, which is typically cured at 120°C to 165°C. It might be a little soft until it dries completely, as silicone is permeable to water vapor.

_________________
Mask: Swift™ FX Nasal Pillow CPAP Mask with Headgear
Humidifier: S9™ Series H5i™ Heated Humidifier with Climate Control
Additional Comments: Climateline hose; SleepyHead

-tim
Posts: 710
Joined: Sat Dec 03, 2011 7:46 pm
Location: Melbourne Australia

Re: boiling stuff

Post by -tim » Fri Feb 17, 2012 9:44 pm

In the world of organic chemistry, lots of things start to happen at about 40 °C (104 °F). Some of those things may help or hurt the flexibility. Other things happen at boiling.

If your going to do this, start out with keeping the mask in 40°C water for a while and see if that helps. Then try again at just under boiling and then try boiling. It maybe be warm but not too hot is the right mix.

_________________
Mask: AirFit™ N20 Nasal CPAP Mask with Headgear
Humidifier: S9™ Series H5i™ Heated Humidifier with Climate Control
Additional Comments: Resmeds overpriced SpO2

User avatar
VVV
Posts: 525
Joined: Mon Mar 14, 2011 11:28 am

Re: boiling stuff

Post by VVV » Fri Feb 17, 2012 10:01 pm

archangle wrote:

I'd boil the water, turn off the heat, let it sit for a minute or so and then drop the parts in. Or make something to hold the parts up from the bottom of the pot if you want to actually boil the parts.
srodeman8 wrote:Hi, the best thing to do is to get the water to boiling, then turn it off for a minute and then put in nasal pillows and leave in there for an hour or so, then shake to get all the remaining water out in the bathtub, and then dry out. Be sure it is COMPLETELY dry before using again. A blow dryer may be used. Don't boil, but do the next best thing.
chunkyfrog wrote: I might consider using the steamer,
Robespierre wrote:As long as the silicone parts aren't resting on the bottom of the pot, you won't damage them with boiling water. Boiling water (100°C) should not be hot enough to damage the silicone, which is typically cured at 120°C to 165°C.
I just have to ask, has anyone tried battering and deep frying?
.....................................V