General Discussion on any topic relating to CPAP and/or Sleep Apnea.
-
NateS
- Posts: 1716
- Joined: Wed Dec 14, 2011 8:53 pm
- Location: Kaatskill Mts-Washington Irving
Post
by NateS » Sun Feb 10, 2019 1:27 pm
I tried to search for the answer but didn't succeed.
With my new machine, I chose to create a New User in SleepyHead but the red line fails to show up at the 24 mark and I always liked that.
I know there is a way to turn it on in SleepyHead because it still shows up in my old User file, but after fiddling around for over an hour I am still stumped.
Would sure appreciate someone reminding me how to turn it on. I have scoured preferences but can't find it there.
Thanks in advance for a reminder.
Best wishes, Nate
Central sleep apnea AHI 62.6 pre-VPAP. Now 0 to 1.3
Present Rx: EPAP: 8; IPAPlo:11; IPAPHi: 23; PSMin: 3; PSMax: 15
"I've had a perfectly wonderful evening, but this wasn't it." —Groucho Marx
-
palerider
- Posts: 32300
- Joined: Wed Dec 16, 2009 5:43 pm
- Location: Dallas(ish).
Post
by palerider » Sun Feb 10, 2019 1:42 pm
NateS wrote: ↑Sun Feb 10, 2019 1:27 pm
I tried to search for the answer but didn't succeed.
With my new machine, I chose to create a New User in SleepyHead but the red line fails to show up at the 24 mark and I always liked that.
I know there is a way to turn it on in SleepyHead because it still shows up in my old User file, but after fiddling around for over an hour I am still stumped.
Would sure appreciate someone reminding me how to turn it on. I have scoured preferences but can't find it there.
Thanks in advance for a reminder.
Best wishes, Nate
Right click on the 'leak rate' on the chart itself, then select 'dotted lines' and put a check by 'leak rate upper threshold'.
I also like to do the same on 'flow rate' and turn on the zero line. (these oughta be on by default, I think).
Get OSCAR
Accounts to put on the foe list: dataq1, clownbell, gearchange, lynninnj, mper!?, DreamDiver, Geer1, almostadoctor, sleepgeek, ajack, stom, mogy, D.H., They often post misleading, timewasting stuff.
-
NateS
- Posts: 1716
- Joined: Wed Dec 14, 2011 8:53 pm
- Location: Kaatskill Mts-Washington Irving
Post
by NateS » Sun Feb 10, 2019 1:55 pm
palerider wrote: ↑Sun Feb 10, 2019 1:42 pm
NateS wrote: ↑Sun Feb 10, 2019 1:27 pm
I tried to search for the answer but didn't succeed.
With my new machine, I chose to create a New User in SleepyHead but the red line fails to show up at the 24 mark and I always liked that.
I know there is a way to turn it on in SleepyHead because it still shows up in my old User file, but after fiddling around for over an hour I am still stumped.
Would sure appreciate someone reminding me how to turn it on. I have scoured preferences but can't find it there.
Thanks in advance for a reminder.
Best wishes, Nate
Right click on the 'leak rate' on the chart itself, then select 'dotted lines' and put a check by 'leak rate upper threshold'.
I also like to do the same on 'flow rate' and turn on the zero line. (these oughta be on by default, I think).
Bingo!!!
Thanks
so much, palerider!
No wonder I couldn't remember how to do it!
Regards, Nate
Central sleep apnea AHI 62.6 pre-VPAP. Now 0 to 1.3
Present Rx: EPAP: 8; IPAPlo:11; IPAPHi: 23; PSMin: 3; PSMax: 15
"I've had a perfectly wonderful evening, but this wasn't it." —Groucho Marx
-
palerider
- Posts: 32300
- Joined: Wed Dec 16, 2009 5:43 pm
- Location: Dallas(ish).
Post
by palerider » Sun Feb 10, 2019 2:55 pm
NateS wrote: ↑Sun Feb 10, 2019 1:55 pm
palerider wrote: ↑Sun Feb 10, 2019 1:42 pm
NateS wrote: ↑Sun Feb 10, 2019 1:27 pm
I tried to search for the answer but didn't succeed.
With my new machine, I chose to create a New User in SleepyHead but the red line fails to show up at the 24 mark and I always liked that.
I know there is a way to turn it on in SleepyHead because it still shows up in my old User file, but after fiddling around for over an hour I am still stumped.
Would sure appreciate someone reminding me how to turn it on. I have scoured preferences but can't find it there.
Thanks in advance for a reminder.
Best wishes, Nate
Right click on the 'leak rate' on the chart itself, then select 'dotted lines' and put a check by 'leak rate upper threshold'.
I also like to do the same on 'flow rate' and turn on the zero line. (these oughta be on by default, I think).
Bingo!!!
Thanks
so much, palerider!
No wonder I couldn't remember how to do it!
Regards, Nate
It is fairly well hidden, and not documented *at all*... I can't blame you for not finding it
Get OSCAR
Accounts to put on the foe list: dataq1, clownbell, gearchange, lynninnj, mper!?, DreamDiver, Geer1, almostadoctor, sleepgeek, ajack, stom, mogy, D.H., They often post misleading, timewasting stuff.
